🗻 Ford Focus Test Mode List

Park or Neutral Position Switch Out of Self-Test Range: Wiring, PNP switch/CPP switch, ECM: P1710: No Change In Transmission Fluid Temperature Signal: P1711: Transmission Fluid Temperature Sensor Out of Self-Test Range: Transmission not at normal operating temperature -repeat test: P1712: Trans Torque Reduction Request Signal Malfunction: P1713 Test Mode DTC DTC Description B1202 9202 Fuel Sender Open Circuit B1204 9204 A forum community dedicated to Ford Focus ST owners and enthusiasts. Come join the ZX3 i was able to get into the test mode and realised my temperature never reached the 108-110 as the hose started spraying out water around 100C once the ac was not engaged. I previously bought new hose clamps so i changed the hose and reinstalled the new clamps. Know and behold no more leaks and the fans kicked in. Okay, so earlier today I decided to check out the diagnostic/test mode for the ST. I started the car up and got into test mode just fine. But when I was browsing through all the parameters I was very surprised when I got to the odometer reading. In test mode my odometer reads 17378 while the standard odometer on the car reads 10797. The in.-H 2 O gauge will help you duplicate the test Ford is performing on the vehicle. With the evap test machine and/or in.-H 2 O gauge connected to the gas vapor system, engine running, the CVS deenergized (open) and the CPS energized (open), this should cause the in.-H 2 O gauge to go negative, approximately −2.0 to −4.0 in.-H 2 O. Torque Maximum vs Mode. Boost Control. Boost control is quite complex but intuitive in the EcoBoost platform, as the example ROM is based on a stock car there were not many changes to the boost control strategy required. This list of maps changed in the example ROM are. Maps By Function → Boost Control → Safety Limitations. Max PR to Avoid 0-18=short (0-20 max.) OIL Displays the code (0-255) for the oil pressure switch input to the instrument cluster. Displays the oil pressure reading input to the instrument cluster. Oil pressure gauge will indicate present oil pressure. Normal oil pressure (greater than 6 psi) will display a value between 000 and 176. Checked my temps yesterday using TEST Mode. Ambient temp was 96F - 98 F or around 36C. Idling in Park with AC ON gave me 103C, Idling in Drive with AC ON gave me 113C to 115C (235.4F to 239F). While driving, temps were around 109C (228.2 F). Temp neveer went into the red, but sure scared me. Dtc list I get in test mode - #01 C140_00 #02 C121_00 #03 C151_00 #04 C131_00 We’re the premiere Ford Focus ST forum with discussions on the 2013+ Focus ST If you find a P0246 on your car’s DTC list, you’ll want to make sure you understand the code’s meaning. P0xxx codes, for example, indicate a problem with a specific subsystem. If the P-code contains a “1,” then the problem is with the engine, and it’s a mechanical issue. P1xxx codes, on the other hand, refer to a problem with the Ford: 00-1-2: Parking Brake Control Assembly Concerns: Ford: 00-12-2 (DTC) - P1635 And/Or P1639 Present After Powertrain Control Module (PCM) Or Instrument Cluster Replacement I was just messing around in my 2012 Focus and figured out how to put it in "test mode". I have the base radio/ information screen but I am sure it will work for the higher up model. 1st Step: Get in Car. 2nd Step: On the steering wheel controls on the left. Hold OK Button and the Right Arrow button at the same time for about 5 secs. Haven't seen a compression test how-to for the ST so we wrote a simple on up. Compression testing on this car is very easy and it's a good way to keep track of the car's health especially if you plan on modifying it. Blog : How to perform a compression test on a Ford Focus ST : Stratified Automotive Controls. NimbusST, TrevorGoodchild, crstjohn I have just done the diagnostics check through the dashboard on my focus mk3 and the car has thrown up 6 fault codes. I need urgent help to understand what the codes are and what they mean. c140_00 - 1st dtc. c121_00 - 2nd dtc. 1607_82 - 3rd dtc (there was no letter on the dash) c151_00 - 4th dtc. c214_00 - 5th dtc. Within 10 seconds, the display should change to "test" in LCD font and the needles will do a full sweeping. Release the Button Pressing the button will now cycle through some 17 different modes 1.Shows a Gauge Sweep 2. Shows all 8's on the LCD (LCD TEST) 3. Illuminates all the bulbs on the dash 4. Displays hexadecimal value for ROM level 5. 8tkV9.

ford focus test mode list